The design of a tracking detector for electrons in a magnetic field consisting of a drift chamber is discussed. The chosen materials for its construction must be light to minimize the effects of the subatomic particles interactions with the chamber walls. Low-density materials and very thin wall thicknesses are therefore needed. From a mechanical engineering point of view, it is important to analyse the drift chamber structure and define the conditions to which it is subject in terms of both mechanical loads and geometric constraints. The analysis of the structural response of the drift chamber has been performed through the Finite Element Method (FEM) as implemented in the commercial software ANSYS and (Ansys Composite Pre/Post).

Surface doping of nano/mesostructured materials with metal nanoparticles to promote and optimize chemi-transistor sensing performance represents the most advanced research trend in the field of solid-state chemical sensing. In spite of the promising results emerging from metal-doping of a number of nanostructured semiconductors, its applicability to silicon-based chemi-transistor sensors has been hindered so far by the difficulties in integrating the composite metal-silicon nanostructures using the complementary metal-oxide-semiconductor (CMOS) technology. Here we propose a facile and effective top-down method for the high-yield fabrication of chemi-transistor sensors making use of composite porous silicon/gold nanostructures (cSiAuNs) acting as sensing gate. In particular, we investigate the integration of cSiAuNs synthesized by metal-assisted etching (MAE), using gold nanoparticles (NPs) as catalyst, in solid-state junction-field-effect transistors (JFETs), aimed at the detection of NO2 down to 100 parts per billion (ppb). The chemi-transistor sensors, namely cSiAuJFETs, are CMOS compatible, operate at room temperature, and are reliable, sensitive, and fully recoverable for the detection of NO2 at concentrations between 100 and 500 ppb, up to 48 h of continuous operation.

We have developed a novel and straightforward approach for the green synthesis of reduced graphite oxide (rGO). First, graphite oxide (GO) was prepared by the Hummers' oxidation method, starting from high-surface-area graphite. Then, rGO was generated from GO in aqueous suspension through a UV-irradiation treatment. The influence of different process parameters (including type of UV source, irradiation time and atmosphere) on the GO reduction efficiency was explored and evaluated on the basis of the data acquired by several experimental techniques, such as infrared spectroscopy in attenuated total reflectance mode, X-ray diffraction, UV-vis absorption spectrophotometry, X-ray photoelectron spectroscopy and thermogravimetry. The acquired results allowed identifying appropriate sets of reaction conditions under which GO reduction yield could be maximized. In particular, the highest reduction degree was obtained by exposing GO to UV light in a UV oven for 48 h under inert atmosphere. The reduction strategy developed by us represents an innovative low-cost and easy route to graphene-based nanomaterials, which does not require any stabilizer, photocatalyst or reducing agent. For this reason, our method represents an attractive environmentally friendly alternative approach for the preparation of stable rGO dispersions in large-scale amounts, to be utilizable in disparate engineering applications.

We present a novel low mass drift chamber concept, developed in order to fulfill the stringent requirements imposed by the experiments for extremely rare processes, which require high resolutions (order of 100–200 keV/c) for particle momenta in a range (50–100 MeV/c) totally dominated by the multiple scattering contribution. We describe a geometry optimization procedure and a new wiring strategy with a feed-through-less wire anchoring system developed and tested on a drift chamber prototype under completion at INFN- Lecce .

Inthis paper, we have investigated the possibility to realize a nanocomposite buffer layer for perovskite solar cells, based on polyelectrolyte poly(3,4-ethylenedioxythiophene): poly(styrene sulfonate) PEDOT:PSS and graphene oxide (GO). To this aim, GO, prepared by a modified Hummers method, was mixed with PEDOT: PSS by solvent swelling method and reduced in situ into the polymer matrix through a green and simple method, by using UV radiation. Thin nanocomposite layers were spin coated on different substrates and characterized by several techniques. GO reduction was first analyzed by XPS analyses, monitoring the decrease of the intensity of the peak of the oxygen groups linked to carbon. The grade of the dispersion of GO into PEDOT: PSS was also analyzed by scanning electron microscopy. Sheet resistance measurements of the films with and without GO before and after UV treatment was performed. The thermal stability of the nanocomposites was then evaluated by thermogravimetric analyses. The nanocomposite layer was finally employed in a perovskite solar cell to evaluate the effect of GO reduction on power conversion efficiency. The interface interaction between the nanocomposite and the perovskite precursors was analyzed by contact angle measurements.